Farmer’s Wife QAL – Using templates!

I seriously considered ditching the templates and working out the math for each block as I go along. I love math, and I know that my work is more accurate when I rotary cut my pieces. But I wanted to keep in the spirit of this project, so I’m using the templates from the book. I hand pieced and quilted my first quilt using templates, so this process isn’t new to me.
This time around, I am using my rotary cutter to cut around the templates and I’m machine piecing my blocks. I thought I’d share the process that I use, first I will go through how I prep my templates:
Supplies:
Thin Cardboard (i.e. cereal boxes)
Spray Adhesive
Templates*
Rotary Cutter – it’s best to use a separate blade for paper
Ruler

*A member of the FWQAL flickr group graciously combined all of the book templates onto 15 pages. I used these templates printed at 100% and they are measuring up great! If you need help finding the template document in flickr, let me know. This is not meant to be a substitute for purchasing the book, however. 🙂

 Start by spraying one side of the cardboard with the spray adhesive (I think the templates stick best to the unprinted side of the cardboard). I did this outside. Some people spray the templates and stick them down. I hate getting the adhesive on my fingers, b/c it is tough to get off. So I spray the cardboard!
Take the cardboard inside and lay your templates out. I don’t like to lay any of my templates over the folds in the cardboard. As you lay each piece down, smooth it over with your finger. If there are bumps or wrinkles, you can pull the piece back up and try again. I find it pretty easy to smooth out the bumps without pulling the pieces back up, though.

Wait a few minutes before cutting the templates with your rotary cutter, that will minimize the adhesive that sticks to your ruler. (Adversely, it’s best to stick your templates down immediately. Typically spray adhesive is permanent only right after it’s sprayed.)
When I cut my templates, I line up the solid SEWING line on each template with the 1/4″ line on my ruler. That ensures that I have an accurate seam allowance, regardless of the dashed/cutting lines. (See the red arrows below pointing to the solid SEWING lines.)

 In the pic below, you can see where my ruler is with respect to the dashed/cutting line. Trim all sides of the template the same way. To trim the funky corners like you see on the triangles, I just eyeballed it. You can use a ruler, though.

 This is how the edges of my templates looked after trimming.

 Continue until you have a stack of pretty templates! (I cut all of the templates for my first 8 blocks to get me caught up with the group, and in the future I’m planning on cutting my templates as I need them each week.)

Now that the templates are ready, I will go through how I cut my pieces using the templates and a rotary cutter and ruler.

Supplies:
Templates
Masking Tape
Rotary Cutter and Mat – switch out your “paper” blade at this point
Ruler
Fabric
For reference, I chose the Big Dipper block for this tutorial. It only requires one template!
To start, make a loop with masking tape and stick the loop to the back of the template.
Now stick the template onto the fabric. I cut 4 layers at a time here.
Line your ruler up along one edge of the template. I line up the solid SEWING line on the template with the 1/4″ mark on my ruler.
And trim!
Repeat on all remaining sides (don’t trim those funky corners yet!).
Now to trim the corners, I don’t use a ruler. I just set my rotary cutter on the edge of the corner and press down. I try not to roll my cutter around a lot, because I want a small, clean cut.
Here’s my triangle with 1 part of the corner trimmed.
Repeat with the little bit that is remaining. Line up the rotary cutter, and press down.
Ta-Da!
Repeat until all of your pieces are cut, and piece as desired! You may need to use a fresh piece of masking tape after a few templates. If the template isn’t staying put on the fabric, use fresh tape. You don’t want the templates moving around!
I’ve seen a few blog posts now where people are questioning the funky corners on the pieces. Fussy Cut explains it really well in this post, scroll down for the picture and explanation. They really do improve accuracy in piecing!
Up next, my first few blocks!
Advertisements

5 responses to “Farmer’s Wife QAL – Using templates!

  1. Yes, can you please direct me to the templates on flickr. I have the book and so refuse to print one template/page so I was doing the math, and on weird templates actually measuring them on my computer screen! Yep, I definitely need that flickr page! Thanks.

  2. Thanks for sharing how you did your templates. It's a great help….could you direct me also to the flikr page of templates? Thanks! Your blocks look great!

  3. I found the template page via the forum but I just never could get them to print out right. Don't know what I'm doing wrong.

  4. From Marti Michell has made acrylic templates with double-blunt engineered corners for many years. If you already own some of these template sets, you can use pieces in them to cut 101 of the 111 blocks in Farmer's Wife. Sets A, B, D, N and S are used most frequently.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s